2017 Aluminum Sheet Plate - Flait Aluminum

The Introduction of 2017 Aluminum Sheet Plate

2017 Aluminum sheet plate is is a typical hard aluminum alloy in the Al-Cu-Mg series, with good comprehensive performance and the largest amount of hard aluminum. 2017 Aluminum plate has high strength and good machinability, but poor corrosion resistance. 2017 Aluminum plate is characterized by high hardness, among which the copper content is the highest, about 3-5%; high strength and certain heat resistance, can be used for working parts below 150°C; the temperature is higher than 125 °C, the strength of the 2017 aluminum plate is higher than 7075 aluminum plate. 2017 Aluminum plate belongs to aviation aluminum, which is not commonly used in conventional industries at present. 2017 Aluminum sheet is widely used in aircraft structures, molds, precision parts, rivets, truck hubs, propeller elements and various other structural parts.

The Product Specification of 2017 Aluminum Sheet Plate

Alloy	2017 aluminum sheet plate
Temper	F,O,T3,T4,T351,H112,etc.
Thickness (mm)	1.0-600
Width (mm)	500-2650
Length (mm)	500-16000
Application	Molds, rivets, truck hubs, propeller elements, etc.

Chemical composition:

Alloy	Si	Fe	Cu	Mn	Mg	Cr	Zn	Ti	Zr	Others		AL
2017	0.2-0.8	0.70	3.5-4.5	0.4-1.0	0.4-0.8	0.10	0.25	0.15	-	Single	Total	Balance
										0.05	0.15

Mechanical properties:

Alloy & Temper

Tensile strength

Rm/Mpa

Yield strength

Rp0.2/Mpa

Elongation

Hardness

HBWα

2017-T4

390

245

115

Physical properties:

Alloy & Temper	Thermal expansion coefficient（20-100℃） µm/m•k	Melting point range（℃）	Conductivity 20℃（68°F）（%IACS)	Resistivity 20（68°F）Ωmm2/m	Density（20℃)（g/cm³）
2017-T4	23.6	513-640	34	0.05	2.8

The Product Features of 2017 Aluminum Sheet Plate

2017 aluminum plate surface has no oil spots, no waves, no scratches, no roll marks, neat trimming, and no burrs;
2017 aluminum plate has good machinability, resistivity, spot welding and seam welding performance;
2017 aluminum plate has high strength and certain heat resistance, and can be used as working parts below 150°C; when the temperature is higher than 125°C, the strength of 2017 aluminum plate is higher than that of 7075 alloy.

The Application of 2017 Aluminum Sheet Plate

2017 Aluminum plate is usually used in rivets, general machinery parts, aircraft, ships, transportation, building structural parts, transport structural parts, propeller components and accessories, etc.

Related Products

2A12 Aluminum Sheet Plate

2A12 aluminum plate is a high-strength hard aluminum alloy in the aluminum-copper-magnesium system, which can be strengthened by heat treatment. Its composition is reasonable and its comprehensive performance is good. The spot welding of 2A12 aluminum plate has good weldability, and there is a tendency to form intergranular cracks when gas welding and argon arc welding are used. The machinability of 2A12 aluminum plate is still good after cold work hardening. The corrosion resistance of 2A12 aluminum plate is not high, and anodic oxidation treatment and painting method or aluminum coating are often used on the surface to improve the corrosion resistance.

2014 Aluminum Sheet Plate

2014 aluminum plate is an Al-Cu-Mg-Si series high-strength wrought aluminum alloy, which can be strengthened by heat treatment. The chemical composition of this alloy is similar to that of 2A14 aluminum alloy, it has high strength and good hot workability, and is easy to forge. The performance is basically the same as 2A14. Due to the high copper content of the alloy, its corrosion resistance is poor, and it is prone to intergranular corrosion and stress corrosion. Its weldability is still good, and its cutting performance is good.

2024 Aluminum Sheet Plate

2024 aluminum plate is a typical hard aluminum alloy in the aluminum-copper-magnesium system. Its composition is relatively reasonable and its comprehensive performance is good.

7050 Aluminum Sheet Plate

7050 aluminum plate is a cold-treated forging alloy with high strength, which is far better than mild steel. The main alloying element of 7050 aluminum plate is zinc, which can be heat treated and strengthened, has good thermal deformation performance, wide quenching range, high strength and good welding performance. 7050 aluminum plate is mainly used for high-stress structures with high strength requirements and strong corrosion resistance, such as mold processing,

7020 Aluminum Sheet Plate

7020 aluminum plate belongs to medium and high strength Al-Zn-Mg alloy, which has high strength, good welding performance and process performance. It is the main welding structural material for aerospace vehicles and ground vehicles and equipment, and is widely used in the manufacture of high-speed train vehicles. body. 7020 aluminum alloy has good comprehensive properties after heat treatment. The strength of 7020 aluminum plate is greater than that of 6082, but its forming ability is correspondingly worse.

7005 Aluminum Sheet Plate

The 7005 aluminum plate is a super duralumin, with good welding performance and can be strengthened by heat treatment. Its strength is not as good as 6061, but it is much lighter. It is a typical lightweight aluminum material. 7005 aluminum plate is often used in welded structures with high strength and high fracture toughness, such as vehicle trusses, rods, containers; large heat exchangers, and parts that cannot be solidified after welding; it can also be used to manufacture sports equipment such as Tennis racket and softball bat.

7075 Aluminum Sheet Plate

The 7075 aluminum plate is an Al-Zn-Mg-Cu series alloy, which can be heat-treated and strengthened. Among them, Zn and Mg mainly play the role of strengthening, and the role of Cu is mainly to improve the corrosion resistance of the alloy. 7075 aluminum plate is a superhard aluminum alloy with very good mechanical properties. The tensile and shear strength can reach more than 600, and the elongation rate can reach as high as 70%.